牛牛天天人人综合影院 焕尧机电关于高温应变片怎么选-美国HPI（三）

上海焕尧机电设备有限公司 

威廉工业控制

您身边的欧洲工业自动化代购专家

品牌负责：程工（William）
Adress：中国上海市嘉定区嘉定新城
 

询价请认真对待，公司设有统一的黑名单制度

愿每一份报价都被温柔以待！！！

原厂 传感器 编码器 流量计 阀泵 夹具 电机 检测器 风扇 减速机 控制模块、隔离放大器、变送器、逆变器、变频器、总线模块、电容、流量开关、接近开关、光栅尺、读数头、绝缘检测仪、远程报警器、分析仪、数据采集器、温控仪、传动轴、轴承、轴套、接头、刹车片、伺服阀、泵、滤芯、密封圈、过滤器

您只需提供品牌+型号（附带铭牌）
优势电气类：P+F、Balluff、Turck、Phoenix、SUCO、MURR、Burster、B&R、Jumo、Schunk 、CON-TRINEX、Voltcraft等 
优势液压类：Rexroth、Hydac、蒙特贝Z92、Parker等各类德国进口工控备件

美国Hitec Products，Inc(HPI）在应力计行业拥有超过50年的经验，HPI是恶劣环境传感器和应力计配件的主要供应商。
美国HPI的应变计广泛用于高温和防水环境下的动态和静态应变测量。

能测试温度达到850°C的高温应变片

SPECIFICATIONS:

Gage Grid: .......................Fe Cr Al Alloy (.001") .003mm diameter round wire
Leads: ..............................Fe Cr Al Alloy (.003") .008mm diameter round wire
with “Z” configuration flattened to (.0015") .004 mm
in grid area
Carrier: ............................Fiberglass reinforced Teflon tape carrier with silicone
adhesive (shelf life of grid carrier [Figure 2] is 9 months)
Resistance: ......................120.0 ohms ± 2.0 ohms at 20°C (68°F)
Gage Factor: ...................2.4 nominal at 20°C (68°F)
Gage Current: .................30 Milliamperes, max.
Temperature Range: ......Cryogenic to 850°C (1560°F)
Weldable Gage ONLY:
Shim Material: ................Hasloy X
Bonding Matrix: .............Alumina
Shelf Life: ........................Unlimit

Density: ............................................................. 7.1 Mg/m3 (0.256 lb./in3)

Chemical Analysis, Approx.: ....................... 72 Fe 22.5 Cr 5.5 Al
Resistivity @ 20°C (68°F): ............................ 875, ohms - cmf
Max. Operating Temperature: ................... 1375°C (2500°F)
Melting Point, Approx.: ................................ 1510°C (2750°F)
Temperature Factor,
Resistant Max. Temp.: ................................... 1.044
Thermal Expansion, ppm/°F: ..................... 20 - 250°C = 6.1 (68 - 482°F)
20 - 500°C = 6.9 (68 - 932°F)
20 - 750°C = 7.7 (68 - 1382°F)
20 - 1000°C = 8.3 (68 - 1832°F)
Gage Factor K @ 20°C (68°F): .................... 2.3 to 2.6
Gage Factor vs. Temperature
Coefficient:................................ -5.73 x 10-4/°C
Tensile Strength, PSI: .................................... 140,000 (hard), 92,000 (soft)
Tensile Strength, MPa: .................................. 965 (hard), 690 (soft)
Elongation, % (Soft): ..................................... 22%
Magnetic: ......................................................... Yes, below 540°C (1000°F)
Thermoelectric Potential vs. Cu: ............... -2.6μV/°C (0-100°C)